Showing results: 196 - 210 of 268 items found.
-
MCP9600 (Screw Terminals) -
SparkFun Electronics
The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 can read both the ambient temperature and the temperature of whatever you're trying to measure! The MCP9600 can do both with a resolution of 0.0625°C, and an accuracy of ±1.5°C (worst-case). The MCP9600 Thermocouple Amplifier is one of our many Qwiic compatible boards! Simply plug and go. No soldering, no figuring out which is SDA or SCL, and no voltage regulation or translation required!
-
Analog Devices Inc.
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
HV200/5 -
Anfatec Instruments AG
The HV200/5 is a high-precision HV-amplifier designed for the control of tube scanners. It takes three input voltages In X, In Y and In Z (-10 V to + 10 V), amplifies them separately (input gain switches: x1, x2, x5, x10, x20) and adds an offset voltage between -10 V and +10 V. In a 2nd stage, the signal is amplified by a factor of 20. This enables its use as HV amplifier in scanning image acquisition applications, such as STM or AFM, with the capability to shift the scan range in high resolution imaging.
-
Encore Electronics, Inc.
Encore Electronics offers a complete line of compact, economically priced instrumentation packaged in standard DIN rail mounted enclosures. Our products include frequency to voltage converters, strain gage amplifiers, notch filters, accelerometer conditioners, and line drivers. Overall package sizes are 3.1″ x 3.3″ x 0.9″ tall (single wide) or 1.6″ tall (double wide).
-
W-IE-NE-R, Plein & Baus GmbH
NIM "Nuclear Instrument Module" is the oldest and simplest nuclear electronics standard. Created in 1969 with AEC report TID20893 (Dec 1969), it defines a powered bin and plug in modules. NIM is the perfect standard for small and flexible setups for high resolution measurements with analogue electronics (amplifier, high resolution analog to digital converter, timing electronics as well as for low / high voltage supplies).
-
W-IE-NE-R, Plein & Baus GmbH
NIM "Nuclear Instrument Module" is the oldest and simplest nuclear electronics standard. Created in 1969 with AEC report TID20893 (Dec 1969), it defines a powered bin and plug in modules. NIM is the perfect standard for small and flexible setups for high resolution measurements with analogue electronics (amplifier, high resolution analog to digital converter, timing electronics as well as for low / high voltage supplies.
-
F30PV -
FLC Electronics Inc
The F30PV is a very fast general purpose linear amplifier having a variable amplification of 0-10 times and capable of bipolar voltage output of ±35V. Any functiongenerator or arbitrary waveform generatoror any othe signal source can be used as an input device. The amplifier's output is linear from DC up to ca 10 megahertz range. It can be used in a wide range of high speed applications.
-
Teledyne Defense Electronics
Teledyne RF & Microwave offers Voltage Controlled Oscillators (VCOs) utilizing bipolar transistors & silicon varactors over the frequency range of 40 MHz to 18GHz. Many of the VCO designs incorporate internal filtering, regulation & amplifiers to meet total system requirements in a small integrated package. Additionally, our hermetic hybrid designs can be screened to the most demanding military and space applications.
-
Teledyne Defense Electronics
Teledyne RF & Microwave offers Voltage Controlled Oscillators (VCOs) utilizing bipolar transistors & silicon varactors over the frequency range of 40 MHz to 18GHz. Many of the VCO designs incorporate internal filtering, regulation & amplifiers to meet total system requirements in a small integrated package. Additionally, our hermetic hybrid designs can be screened to the most demanding military and space applications.
-
CT-1 -
Micro Control Company
Burn-in Board Coninuity Tester. Verifies burn-in board continuity and component tolerances. 768 I/O channels, can be forced to the constant current source or grounded independently. Highly accurate measurement of resistance, voltage, and capacitance using a pair of precision instrumentation amplifiers.
-
Texas Instruments
voltage-output, current-sensing amplifier family that integrates an internal shunt resistor to enable high-accuracy current measurements at common-mode voltages that can vary from 0 V to 36 V, independent of the supply voltage. The device is a bidirectional, low- or high-side current-shunt monitor that allows an external reference to be used to measure current flowing in both directions through the internal current-sensing resistor sensor. The integration of the precision current-sensing resistor provides calibration equivalent measurement accuracy with ultra-low temperature drift performance and ensures an optimized Kelvin layout for the sensing resistor is always obtained.
-
Model 640 -
TREK, INC.
Trek’s Model 640 Electrostatic Chuck Optimizer system is a diagnostic tool which enables evaluation and optimization of waveforms/voltages for electrostatic chucks/clamps in order to minimize de-clamp time, maximize clamp force, and achieve optimum wafer processing for ESC systems. Model 640 combines two amplifiers (for two-phase voltage combinations) and a waveform generator, which can be independently programmed and configured to investigate, research, and discover the perfect power supply and waveform recipe to efficiently drive an ESC application. An electrostatic voltmeter (ESVM) is included to monitor residual voltage from the clamping/de-clamping process.
-
A800DI -
FLC Electronics Inc
This unit contains two independent A800 amplifiers that share common ground reference and power supply. Please see A800 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase.
-
Model 20/20C -
TREK, INC.
The Model 20/20C is a DC-stable, high-voltage power amplifier used in industrial and research applications such as electrostatic deflection, electrophoresis research, dielectric studies, and accelerated life-testing of high tension cables for power transmission. The Model 20/20C provides precise control of output voltages in the range of 0 to 20 kV DC or peak AC with an output current range of 0 to 20 mA DC or peak AC.
-
STMicroelectronics
ST's wide range of rad-hard QML-V qualified analog ICs covers analog-to-digital converters (ADC) and digital-to-analog converters (DAC) for telemetry, instrumentation and imaging applications. Our portfolio also includes rad-hard op amps, high-speed differential amplifiers up to 1 GHz, shunt voltage references and comparators to ensure a complete solution for signal conditioning, referencing and data conversion.
